Construction

How to Install Electrical Switches

In construction of house or building, electric work also needs proper attention at the time of laying pipes, wiring and fixing various fittings including their quality and specifications. All electric fittings such as ceiling rose, wall sockets, switches, regulators and accessories are attached to wall or ceiling. Brass screws shall be used for attaching fittings to their base blokes.
 
Switches and Sockets:
 


The Switches and Sockets should be manufactured with superior quality material such as plastic material and polycarbonate plastic that provides standard functionality. The Switches & Sockets should be flexible in designs, low power consumption and have safe functioning. The Switches & Sockets should be ISI marked and manufactured according to ISI 3854-1997, IS1293-1983. The Switches & Sockets are available in 6Amps, 16 Amps, 25 Amps.

Main Switches:

  • All main switches should be of the ironclad type manufactured by reputed manufacturer.
  • All switches and circuit breakers shall be constructed and installed in accordance with latest guidelines from the I.E.E. Regulations.
  • Handles of switches should be fastened properly, leaving no tendency to unscrew and become loose.
  • All tumbler switches must be of bakelite.
  • In earthed system, all single-pole switches on 2-wire circuits controlling lights, fans etc must be inserted in outer or phase wire as the case may be.
  • In insulated D.C. systems, such switches are to be inserted in the positive side.
  • All unlinked single-pole switches throughout an installation shall be fitted in the conductors or connected to the outer or phase conductors of the supply, or in two way system of supply, in the same conductor, which shall not be a conductor earthed either with or without a circuit breaker or added resistance in the earth connection.
  • In no case shall the consumer insert any single pole switch, cut out or permit such switch, or cut out to be or remain inserted in any earthed neutral conductor.
  • A fuse or unlinked single pole switch shall not be inserted in:
    • The middle or neutral conductor of a three-conductor circuit supplied from a direct current or single- phase-three-wire system.
    • The common return of a two-phase three-conductor circuit.
    • The neutral of a three-phase four-conductor circuit.
    • That conductor of an installation, which is permanently earthed at the source of supply without a circuit breaker or added resistance in the earth connection.

Installation of Main Switches:
In the installation of main switches, main and branch distribution boards the following requirements shall be full filled:

  • A small bracket for pilot lamp shall be fixed and connected through an independent single pole switch.
  • Connections shall be arranged as far as possible to form their own diagram.
  • Each circuit shall be clearly numbered, from left to right.
  • Iron clad switches and distribution boards shall be mounted on 2”x2”x1/4” angle iron frame covered with 1/8” thick iron sheet covering or in recessed cast iron boxes.
  • The casing shall be connected with the main switches and distribution board through flexible metal pipes.

Wall Sockets:

  • All walls socket points shall include a switch and a fuse mounted along side the wall socket.
  • The connections between the switch, the fuse and the wall socket are to be so arranged that the switch be on the live side of both the fuse and the wall socket.
  • In earthen systems, the switch and the fuse may be of the single pole type connected in the outer or phase wire.
  • In insulated system, a double-pole linked switch must be used.
  • All wall sockets shall be of 3-pin type.
  • The 3rd pin shall be earthed through S.W.G. No8 G.I. wire run under casing.
  • The bonding of 3rd pin with the G.I. earth wire shall be done by means of stranded G.I. wires.
  • The bonding of 3rd pin wall socket in the case of T.R.S. system of wiring shall be done through No.14 S.W.G. bare copper wire run between cables and taken direct to the 3rd pin.
;
Avoid daily short circuit and overloading with the use of MCB(miniature circuit breaker), and save your electrical appliances from short circuit.
Do you know what you should know before hiring an electrician? You are responsible for all electrical faults and its repair. You need to hire an electrician for repair of electrical faults. The following checklist should help you when hiring an electrician.
Low quality materials, unqualified electrician and a little carelessness in electric works can cause fatal electric shocks in home. Such accidents are not easy to repair and compensate. So it is essential to take every care while doing electrical fittings during construction of your house. This article gives some tips on electrical works during house construction.
Electricity can be deadly if not used with utmost care. When the phase or live wire touches our body, electric current gives shock depending on the intensity of voltage and paralyze muscular functions of the body. To avoid electric shocks during electric works/contact, make sure you have followed all precautions of electric shock mentioned in the following article.
Electric fitting must be safe and ensure proper safety to the occupants of the house. Low quality products or appliances can cause fatal accidents like short circuit fire/smoke, break out of fire in entire house, current-shock to any member etc.
Saving electricity not only adds to your money but will help thousands in demand of energy also.It’s duty of every citizen to use appliances in proper way.
Sometimes due to carelessness or ignorance, electric phase (Live) wire comes in touch with human body and the current flows through the body as the body is good conductor of electric current.
We all need power to run electrical appliances and different gadgets in our home. For proper distribution of electricity we need to install and maintain the quality wiring by an expert electrician. Following tips will help you understand wiring installation process for your home or office.
Electrical mistakes are common in each and every house that may be dangerous for residents. When you are designing your dream home it may be that you are not aware about the electrical mistakes and its effects. Here are discussed some common electrical problems that can be harmful for residents.
These are three types of faults in electrical fitting: .Open Circuit Fault .Short Circuit Fault .Earth fault and Leakage Fault
The tools for electrical fitting in home: Connector Screw driver (10 cm),Neon Tester,Adjustable Screw Spanner (15cm)
Fluorescent light tubes come in many shapes and sizes. An increasingly popular one is the compact fluorescent light bulb (CF). A fluorescent lamp produces much useful visible light which require only 1/3 to 1/4 of the input electricity.
The breadth and thickness of the strips should be checked.Spacing of screws for fixing strips should be checked.
Check width and depth of the channel, the quality and size of the bricks for mechanical protection.Whether cable identification tags are provided or not.
Brands of electrical materials-Cables-Skytone
Kota stone flooring is a subtle blend of grandeur and luxury giving the interior and exterior a gorgeous look.......
To get maximum ventilation and natural light in your house, make sure the building is properly oriented. Orientation of building saves energy and provides comfortable living as well. This article tells you about various factors and benefits of building orientation.
Preview some of the most impressive pictures of kitchen from GharExpert Gallery.
A solid roof on building is very important for everybody living in the house. The roof should be constructed in a way that assures you great safety. Here are given details about different types of roofing.
Frames of doors and windows are most important parts of your doors and windows. They are available in different size, height, width and shapes. Frames hold locks and hinges and support door and windows to shut and open easily. Here is what you need to know about different doors and windows frames.


fire place - ready to install
fire place - ready to install
Rocker Switch
Rocker Switch
Reverse / Forward Switches
Reverse / Forward Switches
Pneumatic Proximity Switches
Pneumatic Proximity Switches
Cam Operated Rotatory Switches
Cam Operated Rotatory Switches
MCB Switches
MCB Switches
Electrical fitting..
Electrical fitting..
Electrical dealers in bangalore
Electrical dealers in bangalore
switches
switches
Rocker Switch
Rocker Switch
switches
switches
Pneumatic Proximity Switches
Pneumatic Proximity Switches
MCB Switches
MCB Switches
Reverse / Forward Switches
Reverse / Forward Switches
Cam Operated Rotatory Switches
Cam Operated Rotatory Switches
Standard quality wires
Standard quality wires
fire place - ready to install
fire place - ready to install
three phase conductor cables
three phase conductor cables

Contact us About us
Copyright 2007- GharExpert.com All rights reserved.